A Practical Guide To Repairing Your TPE Sex Doll | naughtydownunder

How to Repair TPE Sex Dolls: A Complete Guide

Maintaining and repairing your TPE (Thermoplastic Elastomer) sex doll is easier than you think. Whether it's minor pressure marks or more serious tears and abrasions, this guide will show you how to restore your doll to like-new condition, ensuring long-term enjoyment and durability.

KEY TAKEAWAYS

This is how to practically repair your sex doll:

1) Minor damages like indentation marks on a TPE sex doll can be repaired using the hot towel procedure or the hair dryer method.
2) The hot towel procedure involves applying a hot, wet towel to the damaged area and gently massaging it until the indentation disappears.
3) The hair dryer method uses heat to gradually remove pressure marks and indentations on the sex doll's surface.
4) For more severe damages like tears or abrasions, TPE glue is a recommended option for repair.
5) Clean the damaged area with isopropyl alcohol before applying TPE glue, then hold the tear together until the adhesive sets.
6) The heat gun procedure can be used to fix abrasions on the TPE sex doll's skin, but it requires precision and caution.
7) When dealing with facial cuts and tears, it's advisable to consider purchasing a new sex doll head instead of attempting complex repairs, especially if you're not experienced in doll repair.
8) The time required for repairs will depend on the extent of the damage, and major damages might not be recoverable.

 

Fixing Pressure Marks & Indentations

Over time, your sex doll may develop pressure marks, dents, or indentations from improper storage or heavy objects pressing on the skin. These are minor issues and can be easily fixed using heat methods.

Option 1: Hot Towel Method (Simple & Safe)

  1. Place a clean, hot wet towel (around 60°C) on the indentation for 5–10 minutes.
  2. After removing the towel, wear white gloves and gently massage and pat the area until the dent disappears.
  3. Repeat if necessary.

Tip: This method is safe, even for beginners, and works well for most surface-level dents.

Option 2: Hair Dryer Method (Quick & Easy)

  1. Cover the pressure mark with a damp white cloth.
  2. Apply heat using a hairdryer for 3–5 minutes, keeping a safe distance to avoid overheating.
  3. Massage the area as you apply heat, and the mark will start to disappear.

Note: TPE can withstand high heat up to 200°C, but use moderate settings to avoid damage.

Repairing Tears and Abrasions

More severe damage like cuts, tears, and abrasions can happen due to sharp objects, incorrect use, or storage issues. These can be repaired effectively with TPE Repair Solvent/Glue or a Heat Gun, depending on the severity.

Using TPE Repair Solvent or Glue

TPE Repair Solvent (also known as TPE Glue) melts and fuses TPE material back together, restoring the skin’s appearance and strength.

Step-by-Step Repair Using TPE Glue

  1. Clean the area thoroughly using 70% isopropyl alcohol to remove dirt and oil.
  2. Gently open the tear with your fingers.
  3. Use a toothpick or cotton swab to apply a thin layer of TPE glue to the inside of the tear.
  4. Hold the wound closed firmly for a few minutes until the bond sets.
  5. Let cure for 24 hours in a neutral position to prevent tension on the repaired area.

Important Notes

  • Never "pour" or "drop" glue—apply sparingly.
  • Avoid touching excess glue with fingers—use cloth to gently wipe any residue.
  • Ensure the doll is laid in a way that prevents pulling on the repair site during curing.
  • 3M 94 Primer is widely accessible and can be used in place of TPE glue if needed.

Fixing Abrasions with a Heat Gun

For abrasions and rough skin patches, a heat gun method can restore smoothness when done carefully.

Step-by-Step Heat Gun Method

  1. Clean the area with 70% isopropyl alcohol.
  2. Apply a thin layer of baby oil or Vaseline to protect the TPE from burning.
  3. Hold the heat gun 4 inches away and heat until you see a slight glossy effect (approx. 110°C melting point).
  4. Use a clean cloth to smooth out abrasions while the material is soft (work quickly—about 30 seconds).
  5. Repeat heating and smoothing if necessary.
  6. After cooling, apply powder for a soft, matte finish.

Tips for Heat Gun Repair

  • Use a heat gun with a temperature sensor for better control.
  • Test on scrap TPE material if available before working on your doll.
  • Reapply baby oil between each heating session to prevent drying.
  • Always work in a well-ventilated area and wear a mask to avoid inhaling fumes.

Repairing Facial Cuts (What You Should Know)

Facial cuts are delicate and require experience to fix properly.

Recommendation:

  • For small facial cuts, experienced users can use TPE glue with extreme caution.
  • Beginners should avoid facial repairs—a replacement head is often a better solution.

Bonus Tip: Buying a second head is not just a repair option—it adds variety to your doll's look and personality.

Final Thoughts & Our Promise to You

Repairing your TPE doll is a practical skill that ensures longer enjoyment and protects your girl.

Quick Summary of Repair Options

  • Hot Towel or Hairdryer for dents and pressure marks.
  • TPE Glue for tears and cuts.
  • Heat Gun for abrasions.
  • New head for extensive facial damage.

At SxDolled, we are committed to helping you care for and enjoy your doll for years to come. We provide free shipping on all orders and only stock certified, high-quality dolls from the best manufacturers worldwide.

Need Help or Customizations?

If you have questions about repairing your doll or want to customize the perfect TPE or silicone doll, contact us anytime.

Back to blog

Leave a comment